Princeton-tec CHARGE - MPLS Manuel d'utilisateur télécharger pdf

FINISHED FOLD SIZE - 2.5” X 1.125”

www.princetontec.com

Operating and Maintenance

BedienungsanleitungInstructions

Notice d’utilisation et d’entretien

CHARGE

ENGLISH

If the light has been on for more than two

seconds in any mode, pressing the button

will turn the light off.

Mounting System

Charge is compatible with the following

mounting systems: Helmet Rail, Helmet

Mount, and MOLLE/PALS.

1. Charge is designed to attach directly

to the OPS-CORE ACH – ARC Helmet

Rail System. Charge can mount to either

left or right helmet rail. Slide Charge

dovetail into open end of helmet rail. The

locking tab and spring-loaded ball bearing

engage detents and secure Charge.

2. Helmet mount: LEFT SIDE mounting is

recommended to keep low prole. While

it is possible to mount Charge/Helmet

Mount on right side, this increases risk of

snagging. Remove screws from the plastic

mounting plate and choose the appropriate

metal U-clip. Slide the U-clip onto the bot-

tom edge of the helmet. If excessive play

is present, bend the metal clip with pliers

until there is about 1mm of play between

the clip and helmet. Attach the plastic

mounting plate on the outside of the hel-

met. Holding the metal mount tight against

the bottom of helmet edge, tighten both

screws until secure. Slide Charge dovetail

into open end of helmet mount. The lock-

ing tab and spring-loaded ball bearing

engage detents and secure Charge.

3. MOLLE/PALS mount: Slide MOLLE

mount onto any strap position, then line

up Charge with open end of MOLLE

mount and slide the two together. The

locking tab and spring-loaded ball bearing

engage rail detents to secure Charge.

Specications

Maxbright = 55 Lumens, 28.6 meters

Burnme - Lithium

Modes Hours

Maxbright White 4.32

Ultrabright High 22.65

Ultrabright Low 45.74

Burnme - Alkaline

Modes Hours

Maxbright White 1.51

Ultrabright High 12.19

Ultrabright Low 50.65

Troubleshooting

If the Charge fails to light:

• Check battery for proper installation.

• Replace battery if proper installation

is confirmed.

• Check the light for water contamination

on the circuit board by removing the ve

screws located on the back of the light

body. Remove batteries if there is water

in the electronics, and cease use until the

light has completely dried out. If moisture

accumulates inside the lens, remove the

bezel with a small screwdriver and open

the lens to allow moisture to evaporate.

USA– International 1-Year Warranty

WARRANTY – Princeton Tec warrants

this product to be free from defects in

workmanship and materials under normal

use for as long as you own this product.

This warranty covers all of the component

parts of the product except batteries. This

warranty does not cover deterioration due

to normal wear or damage due to misuse,

alteration, negligence, accidents, or unau-

thorized repair. Princeton Tec

will repair or replace parts which are

defective in workmanship or materials.

Your authorized Princeton Tec Dealer

and Princeton Tec are the only facilities

authorized to repair the product. After (3)

unsuccessful attempts (within the war-

ranty period) to repair the product, you

have the right to elect replacement of the

product or a refund of the purchase price

less allowance for use of the product.

NO INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARE INCLUDED IN THIS

WARRANTY. (Some states do not allow

the exclusion or limitation of incidental or

consequential damages, so the above

limitations or exclusions may not apply

to you.) This warranty gives you specic

legal rights, and you may also have other

rights which vary from state to state.

Princeton Tec reserves the right to change

product specications without notice.

Return Policy

If your light fails to operate, follow these

simple steps:

1) Check battery. Replace if necessary.

2) Contact Princeton Tec customer

service at 800-257-9080 to request RMA

number. No warranty repairs accepted

without RMA number.

3) Return the light without batteries for

repair or replacement to: Princeton Tec,

5198 Rt. 130, Bordentown, NJ 08505.

Postage due and freight collect items will

not be accepted.

Princeton Tec

PO Box 8057, Trenton, NJ 08650

Phone: 609-298-9331

Fax: 609-298-9601

www.princetontec.com

Battery Installation Mitch Mount Installation

OPS CORE Instilation

MOLLE Mount

Battery Installation

1 AA - Alkaline (LR03), Rechargeable

NiCad or NiMH

To install battery, grip the light in either

hand with the battery door facing straight

up. Battery door latch should have an ar-

row facing away from you; slide this latch

forward with your thumb and use your

free hand to open battery door. With a

battery installed, spring tension will make

this operation possible with one hand. To

close the battery door, push it closed and

then slide the latch toward you to lock.

Princeton Tec cares about the environ-

ment and recommends recycling batter-

ies. For more information about battery

recycling, see www.batteryrecycling.com.

WARNING

• Always remove drained battery immedi-

ately. Remove battery during long periods

of storage. NOTE: Rechargeable NiCad

or NiMH batteries may result in reduced

brightness due to lower nominal voltage.

Switch Operation

Charge has a recessed power button to

prevent accidental discharge. The large

button is textured, making it easy to

locate even while wearing gloves.

Charge has two light sources to choose

from: three Ultrabright LEDs or one Max-

bright LED. Ultrabright LEDs have two

modes: high and low. The Maxbright LED

has one mode.

Charge will turn on in Ultrabright “low”

mode with one button press. By pressing

and releasing the button again within 1.5

seconds of the previous button press,

Ultrabright “high” mode will be selected.

Pressing the button once more will turn

the light off.

Holding the power button down for two

seconds at any point will switch to the

Maxbright light source.

2 MODE

1 2

OPS CORE Instilation 1
MOLLE Mount 1

Résumé du contenu

Page 1 - MOLLE Mount

FINISHED FOLD SIZE - 2.5” X 1.125”www.princetontec.comOperating and MaintenanceBedienungsanleitungInstructionsNotice d’utilisation et d’entretienCHARG

Page 2

FINISHED FOLD SIZE - 2.5” X 1.125”Maintenez le bouton d’alimentation enfoncé pendant deux secondes à tout moment pour faire passer l’éclairage sur la

Commentaires sur ces manuels

Pas de commentaire

Princeton-tec CHARGE - MPLS Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Princeton-tec CHARGE - MPLS. Princeton Tec CHARGE - MPLS User Manual [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Princeton-tec CHARGE - MPLS